Lab Testing Equipment

Laboratory Sublimation Tester / Scorch Tester

The device is used for testing heat resistance of fibers, yarns, fabrics after being dyed with colors.

Digital indicate controller
Testing plate be controlled by heat switch separately
Size of testing plate: 100 x 28 mm
Maximum testing temperature: 300°C
Electric date: 110 / 220 V x 1 Phase
Machine dimension: L55 x W43 x H36 cm

Laboratory Rain Tester

To determine the penetration resistance of fabrics or composites at different intensities of water impact. Simulated rain horizontally impacts fabric samples mounted vertically in a stainless steel bath. Samples are backed with a standardized blotting paper which is weighed before and after each test. The rain is applied via a standardized nozzle. This instrument has been set pump storage tank and pumping to recycle the used water and easy to operate.

Test height: 0.6,0.9~2.1,2.4 meter can be adjusted
Nozzle: ψ1+ 0.01mm x 13 holes
Dimension of water bath: L56 x W42 x H40cm
Level control: 1. It has seven-staged overflow holes (0.6,0.9~2.1,2.4 Meter)
               2. DC motor to control the water volume
Timer: Max.: 999 seconds to set to stop pumping and testing.

Laboratory Mullen Type Bursting Strength Tester

This machine is used to test the strength of corrugated board, cardboard, fabrics, leather and so on. This machine uses hydraulic to expand rubber membrane to rupture the tested sample. This action is used to test the burst strength of sample. The anti-burst strength is the important feature for paper, fabrics, leather and so on. It suits to be the evidence in quality control for package or raw material business.


Pressure gauge: diameter of face is “4” or “5”
Capacity: 5、10、20、50、100  Choose two from these number.
Dimension size: 53 x 40 x 55 cm
Weight: 65 kg

Laboratory Pilling And Snagging Tester

The fabrics and knitted fabrics are easily been pilled in use. According to this, user winds the sample around the rubber tube and put it in the cube box which is 23cm at each side. Every cube box is lined with the standard backing with four samples, and makes them rotated with 60 rpm. For the principle, the operating time of fabrics test is ten hours, knitted fabrics is five hours. The average consequence needs to be compared with the standard pilling grading.

Rotation boxes: A type: 2 pc   B type: 4 pc
Turning space: 23 x 23 x 23cm
Testing speed: 60 rpm
Rubber tube: ψ31 x 150
Accessory: four rubber tubes per box
Dimension size: 75 x 51 x 52 cm
Weight: 50 kg

Laboratory Standard Multi-Source Supply

Multiple light sources reveal the metamerism phenomenon when samples match under one set of lighting conditions and not under another. By using a specially designed color matching such as multi-light, you are assured of more consistent and accurate color matching at all times.

Light sources including: D65, A, UV, CWF, TL84, U30
Resettable hour counter to indicate when lamps must be replaced.
Ultraviolet source can be used by itself or in combination with any of the light sources for detecting and evaluating optical brighteners, whitening agents or fluorescent dyes and pigments.
Meets or exceeds major international standards for visual color evaluation including: ASTM D1729, ISO3664, and CIE.
Electric data: 110 / 220 V x 1 Phase.

Laboratory Color Fastness Rubbing Tester

For fabrics, leather, rubber, cardboard, plastic sheeting and so on, it can do the evaluation for the color fastness of friction and test the adhesion of color after the dyeing sample was rubbed. Binding the white cotton (dry or wet) on the face of friction cone. Using the cone with constant weight and frequency to rub the colored sample smoothly. and then putting the white cotton of cone beside the gray scale to determine the adhesion of color to be the grades of the color fastness of friction. By the way, this machine also test the friction strength of ink and evaluation of degree of abrasion, the test purpose is widely.

Max numbers of samples: 6 pc / per times
Friction cone: 2 x 2 cm、Radius 45 mm
Speed of friction: 30 CPM
Distance of friction: 100 mm
Load weight: 200 g / 500 g (changeable)
Times control: Four digit counter, automatic shutdown when the set number is arrived.
Dimension size: W67 x D38 x H 40 cm
Weight: 60 kg

Laboratory Fabric Streak Analyzer

The function of the Streak Analyzer is to isolate defects caused by physical differences. A fabric swatch is combined with polystyrene sheet film, and the Analyzer produces a plastic impression of a fabric surface by incorporating specific conditions of pressure and heat. The absence of color on the plastic impression ensures that only physical streak effects will be seen. The plastic impression is examined to determine whether the streak alignment matches the streaks observed on the fabric.

If the streak analyzer indicates the same blemished pattern as seen in the fabric, then the blemished stripes are physical in nature. This can relate to several physical causes such as yarn tensions, stitch length, yarn count, twist differences, etc. The frame of this machine is made of stainless steel, the operation board is made of acrylic. Upper and lower plates are made of whole block of aluminum with pressure channel and heating ducts. Using three heating tubes, and every tube is three hundred thirty watts of power. Equipped with special gaskets and high-density packing collar to avoid the gas leakage. The machine is exquisite and convenient to operate.

Power: 110 / 200V × 1PH
Size of sample: 300 x 200 mm
Most of power: 7kgs/cm2
Accuracy of temperature: ± 1°C
Dimension of size: L436 × W375 × H160 (mm)